No Sew Window Treatment In Less Than An Hour

 

I mentioned the other day that I made a no sew window treatment for my daughter’s bathroom.  A very simple, very easy treatment anybody can make.  And I do mean anybody!  So don’t feel too intimidated to try it.  You’ll be surprised at how simple this is and how great it looks.

Check out these step by step instructions and give it a try:

IMG_0728

First get a strip of wood like this 1×3 from Lowes.   If you want a deeper return on the sides you can certainly do that, too.  I chose this size, because it’s all I needed for her bathroom.   Cut it (or have it cut at Lowe’s for free) somewhere between 3 and 6 inches longer than the window itself to allow room for the brackets and good coverage over the window.

IMG_0755 

For the correct measurements:

Measure the width of the board and add the returns for each side to the total measurements.  (Excuse my broken thumbnail – I broke it doing this project!) If your window is 30 inches wide and your returns are 3 inches you will add 6 inches for a total width of 36 inches so the sides of the board will be covered up.  It’s not complicated at all:  the width of the board, plus the depth of the board.  That’s it.  To figure the length a good rule of thumb is 1/4 to 1/3 of the length of the window for the finished length.  (For this treatment you will want to allow enough fabric to give you almost double that length so that when you create the swag you have enough fabric for the correct finished length.)  In my case the length of the window is 72 inches and my treatment’s finished length is 22 inches

IMG_0568

 Fold the fabric in half with the face fabric (the pretty side) on the outside.  Fold in the sides like the picture above.

 IMG_0575

Use fabric glue like this Fabri-tac to secure the edges you turned inside.  Just dot the glue inside the edges and press together to give it a finished look.

IMG_0570

 Wrap the top unfinished edge around the board so that both sides of the board are covered and staple into place. 

IMG_0571

Tuck the fabric around the return edges (kind of like you would the edges of a flat sheet on a mattress) to form a neat fold.  Staple into place. 

IMG_0572

Now you have a long piece of fabric hanging from the board.  In my case since I needed the finished length to be 22 inches (or so) so I started with a length of 44 inches (or so) of fabric.  It hung straight down in a rectangle after it was adhered to the board:  Basically a valance that hasn’t yet taken shape.

 IMG_0573

To create the swag look you are going to take your fingers (both hands) and place them just a few inches in on each side of the valance.   Now start to scrunch upwards like you’re creating a fan or an accordion.  Do this till you get the length you prefer on the outside swag points.  (Remember 1/4 to 1/3 of the length of the window is a good rule of thumb.)

 IMG_0574

Once your length is in place tie off the swag with ribbon.  (You can even use ribbon for your tie’s if you want to.)

IMG_0579

To create the bands or ribbons select the width you’d like.  You can make them skinny or wide, whichever you prefer.  I wanted these a little on the wide side, but I’ve done these before with a skinny band and even rope tassels.  (Rope tassels work really well, too, and using them makes one less step for you to do.)

 IMG_0578

I wanted mine to match the shower curtains I had custom made so I purchased a similar fabric, but in a smaller print, and folded them to the width I wanted – seam in the middle as shown above – careful to turn under the bottom edge for a finished look.  I tacked them down by using the Fabri-tac glue shown above.  I tied them off to the right length with a small black ribbon, but you could tie a knot or a bow, too.  If you prefer you can just do a clean band by looping the band edge up to the board and stapling it into place.

IMG_0708

When you are finished you should have something that looks like this. Ta-da!!!  Not hard at all!  This took me around 30 minutes start to finish.  You can do this – I promise!

I will say, though, that this treatment is better if it’s not a window facing the street or facing the backyard.   Otherwise, you probably want to match the liner fabric to your other windows – usually in a neutral color such as white, cream or beige.  This would result in having to sew on a liner (probably with a band of the face fabric at the bottom so that the liner doesn’t show from the front).  And, this is where custom drapes become necessary for those that don’t have an understanding of this sort of thing and sew really well.  

So remember this treatment is more for a side window, rather than the front or back where the liner can clearly be seen from the outside.

 Now for the candle.  Pretty basic, but here’s how to do it for those of you who might not know:

IMG_0580

Take a basic candle votive such as this.

 IMG_0581

 Cut fabric to fit with enough to turn under the edges.

IMG_0582

Turn in the raw edges in the back and glue together with Fabri-tac.  Finish off with a ribbon of your choice.  The ones with the wire on the edges work best so you can shape them.

IMG_0715

Add a little bling or embellishment if you’d like for fun.

And that’s it!  There you go.  Now you can make a window treatment and a candle cover to snazz up your own space.

Good luck with your own project and Happy Decorating!!!

Weekend Bathroom Re-do

 

Okay, so I admit that occasionally I tend to choose the most inopportune times to start a new project that I’ve been quietly scheming about.  (A little quirk of mine that can prove challenging to the rest of my family!)  The weekend before Thanksgiving was no exception.  I decided it was high time I re-did my daughter’s bathroom.  I’d replaced the lighting sometime ago which left holes in the wall – and, I decided, the color and decor were just  too “Old World “ and frumpy for my stylish 16 year old. 

And once I get the wild hair, well, there’s no stopping me.  So, bad timing and all, I made it my mission to get it done.

IMG_0548 I got in such a hurry to start the project that I forgot to take “before” pictures of the whole bathroom, but, I did take some after I started.  These were the red walls I started with.  Textured and fauxed.

IMG_0551

This is where the holes were.  I had to patch and retexture them on Friday night so that it was good and dry by Saturday in order to paint. 

IMG_0550

I decided it would be fun to add a little bling to the walls for my girlie girl so I placed these rhinestones randomly all over the walls.  I adhered them with a little touch of the same joint compound I used to patch the holes.

IMG_0553

Here is the wall with all the added bling, but before I painted.  I covered the tops of each rhinestone with painters tape, then after I painted I went back with fingernail polish remover and cleaned off the excess paint. (Yes, it was tedious!)

IMG_0554

Because of the dark walls I had to prime it first.  I had the primer tinted with the same green color as the paint for faster, better all over coverage.  The paint color I used was Sherwin Williams color Clary Sage.

IMG_0555

IMG_0556

I can’t lie, this project reminded me of how much I hate painting!  I was so glad when I was finished!

IMG_0557 This was the original valance.  Like I said – too “Old World” for an “almost 17” year old.

IMG_0558

 I kept this copper liner fabric on the back and changed the front to black velvet.

IMG_0559

I covered the board with the velvet, then flipped it over and stapled down the edges.

IMG_0560

If you’re super tidy you can go back in with some cording or gimp and trim off the edges to hide the staples.  (I admit I haven’t done that yet!)

IMG_0561 

When it was finished it looked like this in the picture above, but I wanted to embellish it more to give it some oomph. 

IMG_0563

So I painted this black wrought iron ornamental piece an off white color.

 

IMG_0562

And I adhered it onto the cornice board by hanging it on several tiny nails.

IMG_0579

I made a new “no-sew” window treatment for the window to coordinate with the valance over the shower. (I’ll show you how to do this on another blog. It’s a “no-sew” that can be done in 30 to 45 minutes!)

IMG_0583

I recovered Alyssa’s old candle with fabric and ribbon to match the new color scheme. (I’ll show you what I did for this in another blog, too.)

IMG_0707

 And here’s the finished project.  A little less stuffy and and a little more “hip” for my hip daughter.

IMG_0709

  Notice the missing towel at the top?  She keeps using the decorative guest towels.  Grrrrrr!!!  Why, I ask you?  Hers are in the cabinet two feet away! 

IMG_0711 A monogrammed candle with green stones and bling.

IMG_0712

 This is better – with all the towels.  I painted the old bronze towel rack an off white to match the new look.

IMG_0713

Maybe this towel rack will keep her towel off the floor?!   What are the odds?

IMG_0714

Pewter accessories for charm.  A little bowl with extra bath gel, lotion and other goodies. 

IMG_0715

A fresh look for an old candle to snazz up the back of the toilet.  (Notice the bling on the wall in the background?)

IMG_0566

These knobs were in her old bedroom on her dresser.  I painted the center of each one – changing it from the original turquoise color to her new minty green.  With the black and white zebra they work just fine with her new black and white bathroom.  This saved me money since I didn’t have to go buy new ones.

IMG_0727

It was a challenge cramming this in my life the weekend before Thanksgiving, but now that it’s finished I’m happy with the outcome and glad I did it.  (I’m also glad it’s over and done with, though, I’ll admit it!)

Now it’s on to the next project……..no……they never seem to end!.  Life with a designer is never dull!  Annoying maybe, but never dull!!!

Happy Decorating!!!!!

 

Follow

Get every new post delivered to your Inbox.

Join 170 other followers